hi nick,
it's probably the oil pressure sender/sw. they are pretty cheap and relatively easy to replace. i'd start there and if you still have the problem then i'd start really investigating.
Search found 988 matches
- Wed May 29, 2024 1:59 pm
- Forum: PDQ Powercat Forum
- Topic: High Oil Pressure
- Replies: 2
- Views: 98
- Sat May 25, 2024 7:47 am
- Forum: PDQ Powercat Forum
- Topic: Fender Boards
- Replies: 5
- Views: 236
Re: Fender Boards
we just use the synthetic boards, no wood. they are about 1'x3'x4". for locks we use lines on lifelines and position them on slotted toe rail. for our seasonal docking we do a combination of doubling and end to end on toe rail. we have 4 of them.
- Fri May 24, 2024 6:59 pm
- Forum: PDQ Powercat Forum
- Topic: Fender Boards
- Replies: 5
- Views: 236
Re: Fender Boards
hi, since we left new england and floating docks, we converted to "fender boards" i.e. the ones sold by defender, et al. this year we actually used the built in slots to make "double" length fender boards. they stow easily, are rugged, and give flexible options. i also made hooks...
- Wed May 01, 2024 2:43 pm
- Forum: PDQ Powercat Forum
- Topic: Bowmar hatch gasket?
- Replies: 6
- Views: 2719
Re: Bowmar hatch gasket?
our problem ended up being dirt packed in behind the hinges. we cleaned so far we're ok. related to your problem, we had water in genset compartment floor. after thoroughly checking gaskets and surfaces i noticed some space between the deck and the hatch flange. i removed loose bedding and re-packed...
- Wed Mar 27, 2024 9:50 am
- Forum: PDQ Powercat Forum
- Topic: Charging Battery with Generator
- Replies: 6
- Views: 3858
Re: Charging Battery with Generator
do you know if the charger works successfully on shorepower?
- Sun Feb 18, 2024 3:08 pm
- Forum: PDQ Powercat Forum
- Topic: New MV 34 owners
- Replies: 6
- Views: 1943
Re: New MV 34 owners
heh welby, welcome aboard! first, we too have 3 blade 75's and like you when we got our boat it was way over-propped. i dug thru my records and they are now 16x14. we've had them like that for 18 years (4000 hrs). we run at 3350 rpms and that gives us 13.5 knots. as far as 4 blades vs 3. if you sear...
- Fri Feb 02, 2024 4:34 pm
- Forum: PDQ Powercat Forum
- Topic: Bahamas Tel Cell Phone Service
- Replies: 2
- Views: 1908
Re: Bahamas Tel Cell Phone Service
we used mrsimcard years ago. the advantage you get from him is that your phone is working the minute you get near a tower without going in to get a simcard. we are out of date on the current cellphone market.
- Wed Jan 17, 2024 7:31 am
- Forum: PDQ Powercat Forum
- Topic: Bowmar hatch gasket?
- Replies: 6
- Views: 2719
Re: Bowmar hatch gasket?
thanks alan.
i assume you put the joint between the ends on the bottom. also, did you glue the ends together?
i assume you put the joint between the ends on the bottom. also, did you glue the ends together?
- Tue Jan 16, 2024 12:12 pm
- Forum: PDQ Powercat Forum
- Topic: Bowmar hatch gasket?
- Replies: 6
- Views: 2719
Bowmar hatch gasket?
hi all,
we've developed a leak on one of our rear vertical hatches. as best i can tell the water is running down the vertical hull, over the hatch flange and then i believe getting between the gasket and the glass.
does anyone know what secures the rubber gasket to the glass?
tia
we've developed a leak on one of our rear vertical hatches. as best i can tell the water is running down the vertical hull, over the hatch flange and then i believe getting between the gasket and the glass.
does anyone know what secures the rubber gasket to the glass?
tia
- Sat Jan 06, 2024 2:12 pm
- Forum: PDQ Powercat Forum
- Topic: splash guards and vinyl padding protector on outside stairwells
- Replies: 4
- Views: 2389
- Fri Jan 05, 2024 8:06 pm
- Forum: PDQ Powercat Forum
- Topic: splash guards and vinyl padding protector on outside stairwells
- Replies: 4
- Views: 2389
Re: splash guards and vinyl padding protector on outside stairwells
not sure it's definitive answer, but if you search the forum, i've seen a couple of threads on it(splash guards).
- Wed Dec 27, 2023 11:02 am
- Forum: PDQ Powercat Forum
- Topic: Prop Zinc Wear
- Replies: 4
- Views: 2446
Re: Prop Zinc Wear
a suggestion. if you search this site you'll see a modification to the nut which significantly cuts down on the loosening problem. basically, install a screw from the inside of the nut and then use a nyloc nut to secure the zinc. otoh, if you don't have line cutters, you may want to consider switchi...
- Mon Dec 18, 2023 7:28 am
- Forum: PDQ Powercat Forum
- Topic: Replacement Princess Stovetop
- Replies: 4
- Views: 2431
Re: Replacement Princess Stovetop
hi mac,
did all gas and electrical connection hookup w/o change? did you have to make the cut out bigger?
did all gas and electrical connection hookup w/o change? did you have to make the cut out bigger?
- Wed Nov 29, 2023 4:10 pm
- Forum: PDQ Powercat Forum
- Topic: Queen mattress
- Replies: 3
- Views: 6377
Re: Queen mattress
hi dick,
hello to you and carol. question on the millard. was it an exact fit? any problem with the little slope on the stern side?
hello to you and carol. question on the millard. was it an exact fit? any problem with the little slope on the stern side?
- Fri Nov 24, 2023 9:58 am
- Forum: PDQ Powercat Forum
- Topic: Xantrex Pathmaker
- Replies: 10
- Views: 10180
Re: Xantrex Pathmaker
actually thinking about it, i'm wrong on one point. the power source sense wire is a separate wire and does not connect to one of the studs. other than that what i said above will work.