Search found 272 matches
- Thu Nov 03, 2011 9:44 pm
- Forum: Outboard Engines
- Topic: T9.9 lower end removal questions
- Replies: 10
- Views: 17062
Re: T9.9 lower end removal questions
Magic Time, I have posted on this a long time ago. Do not pound on the cavitation plate. It will break. It is likely the driveshaft splines are stuck in the powerhead. My only success in this was to construct a crude but effective puller. It consists of two 4 X4 wood pieces hollowed out to match the...
- Sat Sep 17, 2011 7:46 pm
- Forum: PDQ Powercat Forum
- Topic: exhaust elbow
- Replies: 13
- Views: 12883
Re: exhaust elbow
Roger to the Rescue, We were motoring down the ICW South of Cape Fear when we came across Roger & Mary prepping "Teamwork" for their annual trek to the Bahamas. I described our Exhaust leak to Roger and Voila, he came up with a used elbow from his boat. I installed it last night after ...
- Thu Sep 15, 2011 10:35 pm
- Forum: PDQ Powercat Forum
- Topic: exhaust elbow
- Replies: 13
- Views: 12883
Re: exhaust elbow
Thanks Ron,Mary,Roger I tried an epoxy stick with no luck. I think the elbow gets too hot for the epoxy. It appears the leak is at the weld between the pipe from the turbo-charger and the larger exhaust pipe over which the hose fits. I am just letting it leak for now until we get the boat to Florida...
- Wed Sep 14, 2011 11:21 pm
- Forum: PDQ Powercat Forum
- Topic: exhaust elbow
- Replies: 13
- Views: 12883
Re: exhaust elbow
My starboard engine exhaust elbow is leaking water all over the motor mount and transmission. Total time is only 1250hrs. Where can I get a replacement that will last? Help please. On the move South to Florida now in Oriental, NC.
Chet
MV34096 / 100HP 4JH3-HTE
Chet
MV34096 / 100HP 4JH3-HTE
- Tue Sep 13, 2011 10:31 pm
- Forum: PDQ Powercat Forum
- Topic: Reading Light Replacements
- Replies: 15
- Views: 17966
Re: Reading Light Replacements
I replaced mine with Dr LED G4MR11 (1W MK II 12V) PN 8001238. They are a direct replacement with no modifications and give a nice warm reading light, remain cool, and have a 50,000hr life. Made in USA. Not cheap (Around $25. ea). Get them on internet or WestMarine
Chet
MV3496
Chet
MV3496
- Tue Jul 26, 2011 8:04 pm
- Forum: PDQ Capella (PDQ 36) Forum
- Topic: Challenge : From beginner to fulltime liveaboards.
- Replies: 11
- Views: 14096
Re: Challenge : From beginner to fulltime liveaboards.
Dominique, My two cents worth says try a "partial" move aboard before commiting to full time. Many Canadian cruisers put their boats on the hard for the Summer months in a Florida boatyard and then move aboard in the Fall to spend the Winter in the Bahamas returning in May before the hurri...
- Tue Jul 19, 2011 5:54 pm
- Forum: PDQ Powercat Forum
- Topic: Anyone installed a boarding ramp?
- Replies: 8
- Views: 10399
Re: Anyone installed a boarding ramp?
Check out the Solvit deluxe telescoping ramp for pets. A fellow boater used one on his boat and it was strong enough for adults and stowed easily.
Chet
Allezcat II / MV34
Chet
Allezcat II / MV34
- Sun Jul 17, 2011 10:55 pm
- Forum: PDQ Powercat Forum
- Topic: Anchor chain hook suggestions
- Replies: 8
- Views: 10420
Re: Anchor chain hook suggestions
I just added two wraps of 3M RUBBER electical tape to my 316SS chain hook. It now no longer falls off the 5/16 ht chain. Not sure how long this fix will last but works great for now.
Chet
Allezcat II / MV34 096
Chet
Allezcat II / MV34 096
- Tue Jul 05, 2011 12:33 am
- Forum: PDQ Capella (PDQ 36) Forum
- Topic: Anyone have PDQ 36 Sail Plan with Measurements?
- Replies: 6
- Views: 9791
Re: Anyone have PDQ 36 Sail Plan with Measurements?
You might Triton Sails (www.tritonsails.com ) They were the supplier for all the early 36 sailboats and supplied replacement sails for my boat about 5 years ago.
Chet
Allezcat 36010
Chet
Allezcat 36010
- Fri Jun 24, 2011 8:19 pm
- Forum: PDQ Powercat Forum
- Topic: Shallow Water Depth Info
- Replies: 2
- Views: 5095
Shallow Water Depth Info
I have the Raymarine E120 with Dm300 depth module. The depth readout quits at 4.3 ft. I installed a P79 transducer and tried plugging it into the Dm300. Same problem. I would really like to be able to read shallow depths as I live in a canal community with very shallow entry channel. Is there some s...
- Fri Jun 24, 2011 8:05 pm
- Forum: PDQ Powercat Forum
- Topic: MV 34 - 4 blade props
- Replies: 64
- Views: 80764
Re: MV 34 - 4 blade props
Installed the new four blade props this week. Initial results are good. WOT gives 3850 RPM (100HP) and 19.9Kts. Cruising speeds are about .5 Kts higher (at the same RPM) and they seem smoother (subjective). Replaced the cutlass bearings also. They are model BITE. Cut the fiberglass housing back abou...
- Thu May 19, 2011 9:20 am
- Forum: PDQ Powercat Forum
- Topic: Cutlass Bearing Replacement
- Replies: 7
- Views: 10779
Re: Cutlass Bearing Replacement
Thanks Ron & John, Just the info I need. Will let you know how this turns out.
Chet
Allezcat II / MV 096
Chet
Allezcat II / MV 096
- Wed May 18, 2011 12:40 pm
- Forum: PDQ Powercat Forum
- Topic: Cutlass Bearing Replacement
- Replies: 7
- Views: 10779
Cutlass Bearing Replacement
I am having props replaced on hull 96 and want to change the cutlass bearings at the same time. Does anyone have the specs on sizing and how does one remove them without pulling the shafts? I have noticed at the higher RPM's (3000), the aft part shaft "whips" around causing the tides marin...
- Wed May 18, 2011 10:18 am
- Forum: Outboard Engines
- Topic: Crack in upper casing
- Replies: 2
- Views: 5745
Re: Crack in upper casing
Hey Evan,
I agree with Duetto. The crack should not cause any problem other than exhaust gas escaping. The JB Weld sounds like a good fix if you can get it to stick.
Chet
Allezcat 36010
Allezcat II MV34 096
I agree with Duetto. The crack should not cause any problem other than exhaust gas escaping. The JB Weld sounds like a good fix if you can get it to stick.
Chet
Allezcat 36010
Allezcat II MV34 096
- Mon May 09, 2011 11:38 pm
- Forum: PDQ Powercat Forum
- Topic: MV 34 - 4 blade props
- Replies: 64
- Views: 80764
Re: MV 34 - 4 blade props
Finally received the new 4 blade props for the 100HP Yanmars from H&H. They are 17R/L Brz Dqx 1-1/4" four blade props from Michigan Wheel. It took 11weeks from ordering! Total cost including frt & tax was $1712.91.
Chet
Allez Catr II / MV 096
Chet
Allez Catr II / MV 096