The Yamaha 9.9 has two plastic intake screens located on each side of the lower unit just below the anti-cavitation plate. Suggest you pull the hose off the plastic discharge fitting first and run the engine to check for water flow from the hose.
Chet
Allezcat 36010
Search found 272 matches
- Mon Jul 25, 2005 12:30 pm
- Forum: Outboard Engines
- Topic: 9.9 cooling intake
- Replies: 3
- Views: 5810
- Fri Jul 22, 2005 12:07 am
- Forum: PDQ Capella (PDQ 36) Forum
- Topic: water heater
- Replies: 17
- Views: 20208
Capthank,
I have the printed version of the Wolter manual. I could copy it and mail it if you wish. Need a mailing address.
Chet - Allezcat
cswhitejr@yahoo.com
I have the printed version of the Wolter manual. I could copy it and mail it if you wish. Need a mailing address.
Chet - Allezcat
cswhitejr@yahoo.com
- Tue Jul 19, 2005 12:32 pm
- Forum: Outboard Engines
- Topic: 9.9 Yamaha Trouble shooting
- Replies: 4
- Views: 7658
Mike Martin on Distant Music had a similar problem. We also had voltage at the starter. It turned out to be a corroded connection of the battery wire at the circuit breaker, which in his boat was mounted in the engine well, a most corrosive environment. You might also check connections at the start ...
- Tue Jun 28, 2005 11:12 am
- Forum: Outboard Engines
- Topic: 9.9 sputters and dies above 1/2 throttle
- Replies: 12
- Views: 14440
Kevin Another quick thought; Check all the fuel hose connections including the connection at the motor. A loose connection will allow air to be sucked in. Also the fuel hose primer bulbs are notorious for causing problems as they have check valves which malfunction. You might consider a replacement ...
- Tue Jun 28, 2005 11:03 am
- Forum: Outboard Engines
- Topic: 9.9 sputters and dies above 1/2 throttle
- Replies: 12
- Views: 14440
Kevin, CDI is abbreviation for Capacitive Discharge Ignition. It is the black box on the port side of the motor about the size of a cigarette box with many wires coming out of it. It controls the spark to both cylinders and often malfunctions causing untold grief. It is a bit of a job to replace but...
- Thu Jun 23, 2005 9:19 pm
- Forum: PDQ Powercat Forum
- Topic: Fueling Concerns....
- Replies: 5
- Views: 8822
Our old PDQ36 gasoline boat used to do the same. Removing the cockpit floor (deck?) I discovered the long vent hose had a sag in it forming a fuel trap which prevented proper venting. I made up several plastic supports and glued them under the vent hose to the top of the aluminum tank so the hose ge...
- Sat Jun 18, 2005 8:46 pm
- Forum: Gear / Equipment / Maintenance
- Topic: Simpson/Lawrence Sprint 1000 neds brushes
- Replies: 2
- Views: 5799
- Mon Jun 13, 2005 10:11 pm
- Forum: Outboard Engines
- Topic: 9.9 sputters and dies above 1/2 throttle
- Replies: 12
- Views: 14440
- Wed Jun 08, 2005 5:19 pm
- Forum: Destinations / Trip Reports / Crew
- Topic: Bahamas bound
- Replies: 3
- Views: 7027
- Tue Jun 07, 2005 8:35 am
- Forum: PDQ Powercat Forum
- Topic: Bottom Paint for electronis
- Replies: 2
- Views: 4954
- Mon Jun 06, 2005 5:21 pm
- Forum: Outboard Engines
- Topic: Battery charging from the 9.9
- Replies: 8
- Views: 10517
- Mon Jun 06, 2005 5:19 pm
- Forum: Outboard Engines
- Topic: Battery charging from the 9.9
- Replies: 8
- Views: 10517
- Mon Jun 06, 2005 5:08 pm
- Forum: PDQ Capella (PDQ 36) Forum
- Topic: water heater
- Replies: 17
- Views: 20208
I have about five Wolters in various conditions. If someone needs parts to rebuild one please let me know. The problem with some of these units was the flow control switch. If it stuck in the off position, the unit would not light. If it stuck in on position the unit would boil out all the water and...
- Mon Jun 06, 2005 4:49 pm
- Forum: Outboard Engines
- Topic: Battery charging from the 9.9
- Replies: 8
- Views: 10517
Hi Sam, As long as the batteries are NOT fully charged there is no problem. If they are fully charged, (like after being plugged in at a dock) you will see the voltage go to 15, 16, 17 .... unless you add load. Gels should never be charged over 14.2V. A wet cell battery will begin to gas when overch...
- Fri Jun 03, 2005 7:26 am
- Forum: PDQ Capella (PDQ 36) Forum
- Topic: Help with spring setup...please?
- Replies: 12
- Views: 13245