Replacement rub rail

Post here if you want to discuss a topic specific to the PDQ Altair.
Post Reply
danhaun
skipper
skipper
Posts: 53
Joined: Wed Jun 22, 2011 6:58 am
Location: (32011)

Replacement rub rail

Post by danhaun »

Hi all,
Has anyone replaced the rub rail on a 32? If so, could you share your experience? Should the new rail be flexible or rigid or semi-rigid?

TomKat has an aluminum rub rail with black vinyl insert that looks very shabby. I notice in photos on Thinwater's blog that the rail is black rubber or vinyl, with a nice looking SS cap and I would like to replace with something like that.

Any advice and experience is appreciated.

Dan Haun
TomKat PDQ32 #11
User avatar
thinwater
admiral
admiral
Posts: 1110
Joined: Mon Sep 22, 2008 8:08 am
Contact:

Re: Replacement rub rail

Post by thinwater »

I suppose it depends on whether you want to protect the boat from pilings, or protect other boats from damage when rafting. For piling protection, the SS cap is excellent, to protect other boats, an insert is better

(I don't know where they are from)
Writing full time since 2014.
"Rigging Modern Anchors,"Seaworthy Press, https://www.amazon.com/Rigging-Modern-A ... 1948494078
Book Store. http://sail-delmarva.blogspot.com/2017/ ... store.html
danhaun
skipper
skipper
Posts: 53
Joined: Wed Jun 22, 2011 6:58 am
Location: (32011)

Re: Replacement rub rail

Post by danhaun »

That makes a lot of sense. Everything is a compromise.

I found a kit from Taco that is the right dimensions and uses what they call a "flex chrome" insert.
http://tacomarine.com/product/V11-9811/ ... ome-Insert
The rail base looks like it would accept the SS cap at 3/4" if the insert proves unstable in UV or otherwise inadequate so I am going with that option.

Thanks for the response.

Dan
User avatar
thinwater
admiral
admiral
Posts: 1110
Joined: Mon Sep 22, 2008 8:08 am
Contact:

Re: Replacement rub rail

Post by thinwater »

Mine look like this. The cap is relatively thick SS, and the body is firm rubber. That is 1" webbing in the photo, so it is at least 2 inches wide.

Image

And do watch the ends. The above is obviously a cutting hazard to mooring bridles, so I filled the space with a carved block of rubber. Worked fine. All it needs to do is keep the rope out of the slot.
Image
Writing full time since 2014.
"Rigging Modern Anchors,"Seaworthy Press, https://www.amazon.com/Rigging-Modern-A ... 1948494078
Book Store. http://sail-delmarva.blogspot.com/2017/ ... store.html
Phenix-former-owner
Site Admin
Posts: 185
Joined: Tue Feb 03, 2004 4:58 pm
Location: Chicago (32007)

Re: Replacement rub rail

Post by Phenix-former-owner »

I see the one from Taco Marine is not sold directly by them, but through their distributor West Marine. If you do this, I would be very interested in the results as the rubrail on Phenix could use a replacement.

Link: https://www.westmarinepro.com/buy/taco- ... --11075298
$449 retail
--
User avatar
thinwater
admiral
admiral
Posts: 1110
Joined: Mon Sep 22, 2008 8:08 am
Contact:

Re: Replacement rub rail

Post by thinwater »

The TACO rail is only about 1/2 the thickness of mine. The rubber block I used was 3/4", plus the bonding under it and the metal cover above it, for a total of nearly 1".

I would ask James Power. I really like having a thick rail that stands out, allowing me to pivot against it when docking, since I mostly singlehand. Better to touch lightly and then slide, than to struggle to avoid any contact and then crunch.
Writing full time since 2014.
"Rigging Modern Anchors,"Seaworthy Press, https://www.amazon.com/Rigging-Modern-A ... 1948494078
Book Store. http://sail-delmarva.blogspot.com/2017/ ... store.html
Post Reply